Cadmium shows up in fewer workplaces than lead, but where it does show up, the rule that governs it is one of the more demanding substance-specific standards in Title 8. 8 CCR §5207, Cadmium, applies to occupational exposure to cadmium and cadmium compounds in all forms, in all industries except construction-related work, which has its own standard. Below are the parts that matter most, with the subsection for each.
The Two Numbers: PEL and Action Level
Section 5207(c) sets the permissible exposure limit at 5 micrograms per cubic meter of air (5 μg/m³) as an 8-hour time-weighted average. Section 5207(b) defines the action level as 2.5 μg/m³, also as an 8-hour TWA.
The action level is the trigger for most of the program. Monitoring frequency, medical surveillance coverage and a respirator-on-request right all key off it, while regulated areas, protective clothing, hygiene facilities and the written compliance program key off the PEL. When I review a cadmium program, the first thing I check is whether the employer has sorted each job into the right bucket: below the action level, at or above the action level, or above the PEL.
Exposure Monitoring
Under §5207(d), the employer must determine whether any employee may be exposed at or above the action level, using full-shift personal breathing-zone samples. Representative sampling of employees with similar exposures is allowed.
- Initial monitoring is required unless the employer has earlier monitoring, taken after September 14, 1991, under conditions closely resembling current ones, or objective data showing exposure will not reach the action level.
- Periodic monitoring: where exposure is at or above the action level, monitoring continues at least every six months.
- Stopping: monitoring may be discontinued only when results are below the action level and a second sample taken at least seven days later confirms it.
- Additional monitoring is required after changes in materials, equipment, personnel, work practices or products that could increase exposure.
- Notice: employees must be notified individually in writing, and results posted, within 15 working days. If the PEL was exceeded, the notice must describe the corrective action.
- Accuracy: the method must be accurate to within plus or minus 25 percent at a 95 percent confidence level at the action level, the PEL and the SECAL.
Regulated Areas and Engineering Controls
Section 5207(e) requires a regulated area wherever exposure is, or can reasonably be expected to be, above the PEL. The area must be demarcated so employees can recognize it, access is limited to authorized persons, everyone inside must wear a respirator, and eating, drinking, smoking, chewing tobacco or gum and applying cosmetics are prohibited inside. The required sign legend is set out in §5207(m)(2)(B).
Section 5207(f)(1) requires engineering and work practice controls to reduce exposure to or below the PEL, except to the extent the employer can show they are not feasible. Several details matter:
- SECALs. For certain processes, §5207(f)(1)(B) and Table I set a separate engineering control air limit, and controls must bring exposure to or below that SECAL rather than the PEL. Table I lists 50 μg/m³ for nickel-cadmium battery plate making and plate preparation; cadmium refining, casting, melting, oxide production and sinter plant in zinc/cadmium refining; calcine, crushing, milling and blending in pigment manufacture; cadmium oxide charging, crushing, drying and blending in stabilizer production; and the sinter plant, blast furnace, baghouse and yard area in lead smelting. It lists 15 μg/m³ for all other nickel-cadmium battery processes, all other pigment manufacture processes, and mechanical plating. Unlisted processes in those industries must meet the PEL through controls. Where exposure stays above the PEL, the respirator provisions in §5207(g)(1) come into play.
- Intermittent exposure. Under §5207(f)(1)(C), the control requirement does not apply where the employer shows the employee is only intermittently exposed and is not exposed above the PEL on 30 or more days per year (12 consecutive months).
- Lowest achievable. Where controls cannot reach the PEL or SECAL, §5207(f)(1)(D) still requires them to reduce exposure to the lowest levels achievable, supplemented by respirators.
- No rotation. Under §5207(f)(1)(E), employee rotation may not be used as a method of compliance.
- Written compliance program. Where the PEL is exceeded, §5207(f)(2) requires a written program, reviewed and updated at least annually, and provided on request to affected employees, their designated representatives, the Chief and NIOSH.
- Ventilation checks. Under §5207(f)(3), local exhaust performance is measured as necessary to maintain effectiveness, and within five working days of any change in production, process or control that might significantly increase exposure.
Respirators, Protective Clothing and Hygiene
Section 5207(g)(1) lists when respirators are required, including during installation of controls, in regulated areas, where feasible controls do not reach the PEL, in emergencies, and where an employee exposed at or above the action level requests one. The program must follow the general respiratory protection standard as §5207(g)(2)(A) directs. Under §5207(g)(3), the employer must provide a powered air-purifying respirator instead of a negative-pressure respirator when the employee chooses one and it gives adequate protection, provide full facepiece respirators when an employee experiences eye irritation, and fit HEPA filters.
Section 5207(i) requires protective clothing at no cost where exposure is above the PEL or where skin or eye irritation occurs at any level. Contaminated clothing is removed at shift end only in change rooms, bagged in sealed impermeable containers and labeled, and cleaned at least weekly.
For employees exposed above the PEL, §5207(j) requires change rooms with separate storage for street clothes and protective equipment, showers at the end of the shift, and washing of hands and face before eating, drinking, smoking, chewing or applying cosmetics. Lunchrooms must be readily accessible, kept free of cadmium, and must not expose anyone at or above 2.5 μg/m³.
Housekeeping under §5207(k) favors HEPA vacuuming. Shoveling, sweeping and brushing are allowed only after vacuuming and similar methods were tried and found ineffective, and compressed air is prohibited unless used with a capture ventilation system.
Medical Surveillance
Section 5207(l)(1)(A) covers employees who are or may be exposed at or above the action level, unless the employer shows they will not be exposed at or above the action level on 30 or more days per year (twelve consecutive months). Certain previously exposed employees are also covered. Examinations are provided at no cost and are performed by or under the supervision of a licensed physician, which is the term the standard uses.
- Initial examination, §5207(l)(2)(A): within 30 days after initial assignment to a job with cadmium exposure, including biological monitoring of cadmium in urine (CdU), beta-2 microglobulin in urine and cadmium in blood (CdB).
- Periodic examination, §5207(l)(4): within one year after the initial examination and at least biennially after that, with biological monitoring at least annually.
- Biological monitoring results, §5207(l)(3): the standard sets levels of CdU 3 μg/g creatinine, beta-2 microglobulin 300 μg/g creatinine and CdB 5 μg/liter of whole blood. A result above any of these requires the employer to reassess exposure within two weeks, correct deficiencies within 30 days and provide a full medical examination within 90 days, with more frequent monitoring afterward. Higher levels set out in §5207(l)(3)(D) can lead to medical removal.
- Medical removal protection, §5207(l)(11)-(12): for up to 18 months each time, the employer must maintain the removed employee’s total normal earnings, seniority and other rights and benefits.
Under §5207(l)(9) the employer must give the examining physician listed information, including a copy of the standard, the employee’s duties and exposure levels. In the programs I review, I check how result deadlines are tracked, not just whether exams occurred.
Training and Records
Section 5207(m)(4) requires training before or at the time of initial assignment and at least annually after that. The content listed in §5207(m)(4)(C) covers health hazards; the quantity, location, manner of use, release and storage of cadmium in the workplace; engineering controls and work practices; what employees can do to protect themselves, including hygiene and smoking; respirator and protective clothing use and limits; the medical surveillance program; the contents of the standard; and the right of access to records.
Under §5207(n), exposure monitoring and objective data records are kept at least 30 years, and medical surveillance records for the duration of employment plus 30 years.
What to Do This Week
- Inventory every process that uses or disturbs cadmium-bearing material, including coatings on parts you weld, cut or grind.
- Pull your most recent personal sampling and sort each job against the 2.5 μg/m³ action level and 5 μg/m³ PEL.
- Check whether any process is listed in Table I and, if so, whether controls are measured against the SECAL.
- Confirm that everyone at or above the action level is enrolled in medical surveillance and that result follow-ups are tracked.
- Verify that annual training and the written compliance program review are current and documented.
If you need cadmium exposure sampling or a review of your compliance program, you can request a consultation or call (626) 546-9384. For help setting up surveillance tracking and records, see the recordkeeping and medical surveillance service, and for broader exposure work, the industrial hygiene page.