Cal/OSHA Section 5155 and Table AC-1: Reading Exposure Limits

By Michael Karl McNeil, REP, RIH, EPP, QSD

Most California employers know Cal/OSHA sets exposure limits for chemicals, dusts, fumes and vapors; fewer have opened the rule itself. That rule is 8 CCR §5155, Airborne Contaminants, and its Table AC-1 is the list most employers are measured against. Reading it correctly is the difference between monitoring that answers the right question and numbers nobody can use. Here is how the section works, how to read a Table AC-1 row, and what it requires for monitoring and medical surveillance.

What Section 5155 Covers

Under §5155(a)(1), the section sets requirements for controlling employee exposure to airborne contaminants and for skin contact with substances designated by the “S” notation in Table AC-1, at all places of employment in the state.

  • Substance-specific standards take over. Section 5155(a)(2) says that when the section references another section for controlling exposure to a particular contaminant, the §5155 provisions for that substance apply only to places of employment exempt from the other standard. If a substance has its own standard, that standard is where you start.
  • Unlisted substances are not a free pass. The note following subsection (a) states that harmful exposure to any substance not listed in the section “shall be controlled in accordance with section 5141.”

When I review exposure programs, a recurring gap is a substance evaluated under Table AC-1 when its own standard applied, or a chemical missing from the table treated as needing no attention.

Three Kinds of Limits: PEL, STEL and Ceiling

Section 5155(b) defines the terms, and §5155(c) turns them into enforceable limits.

  • Permissible Exposure Limit (PEL). Defined as the maximum permitted 8-hour time-weighted average concentration of an airborne contaminant. Under §5155(c)(1)(A), an employee’s exposure in a workday, expressed as an 8-hour TWA, shall not exceed the PEL listed in Table AC-1.
  • Short Term Exposure Limit (STEL). Defined as a 15-minute time-weighted average exposure not to be exceeded at any time during a workday, even if the 8-hour TWA is below the PEL. Section 5155(c)(2)(A) applies it, and adds that if a footnote to Table AC-1 specifies a different averaging period, the TWA over that period shall not exceed the STEL at any time during the workday.
  • Ceiling limit. Defined as the maximum concentration to which an employee may be exposed at any time. Section 5155(c)(3) requires that exposures be controlled so the applicable ceiling in Table AC-1 is not exceeded at any time.

These are separate tests. A full-shift sample under the PEL says nothing about whether a 15-minute task exceeded the STEL, and neither average shows whether a ceiling was crossed during a brief transfer. Build the sampling plan around the limits the substance carries.

Excursions Above the PEL When There Is No Ceiling

For substances that have no ceiling limit, §5155(c)(2)(B) states that employee exposure to concentrations above the PEL shall be controlled so as to prevent harmful effects such as narcosis, significant irritation of the eyes, skin or respiratory tract, or chronic or irreversible tissue change.

A note under that paragraph gives guidelines in a small table headed “PEL Value (From Table AC-1)” and “Multiplication Factor For Maximum Concentration”:

  • PEL value 0 to 1: factor of 3
  • PEL value greater than 1 to 10: factor of 2
  • PEL value greater than 10: factor of 1.5

The note’s footnote says to use the ppm value unless the concentration is expressed only in mg/M3. The operative rule is the “shall be controlled so as to prevent harmful effects” language in (c)(2)(B). The factors appear in a note described as guidelines. I use them as a yardstick for short peaks on substances without a STEL or ceiling, but present them as guidance, not as a listed limit.

How to Read a Row in Table AC-1

Table AC-1 has these columns: Chemical Abstracts Registry Number, Skin notation, Name, PEL (in ppm and mg/M3), Ceiling, and STEL (in ppm and mg/M3). The column headings carry lettered footnote markers, and many individual entries carry their own markers as well. A practical way to read any row:

  1. Match by CAS number, not just by name. Safety data sheet names do not always match the table’s naming.
  2. Check for more than one entry. Some substances are listed in more than one form, such as a total dust entry and a respirable fraction entry. Pick the entry that matches what you are sampling.
  3. Read the units. The PEL and STEL columns each have a ppm and a mg/M3 sub-column, and not every entry fills both. Sample and report in a unit the table actually lists for that entry.
  4. Look at all three limit columns. An entry may show a PEL only, a PEL and STEL, or a ceiling. The Ceiling column holds either a numeric value or a letter designation, depending on the entry.
  5. Read every footnote attached to the row. Footnotes can change the averaging period or define the fraction measured. Skipping them is how correct sampling gets compared to the wrong limit.
  6. Check the Skin column. An “S” triggers the requirements discussed below.

I am deliberately not reproducing values here. The table is amended over time; read any number you rely on from the current table, not a secondhand list.

Mixtures, Long Shifts and the Skin Notation

The Appendix to §5155 sets out the arithmetic. Under Appendix (A), the 8-hour TWA is calculated by multiplying each concentration by its exposure time in hours, summing those products, and dividing by eight. The appendix states that eight is used as the denominator regardless of the total hours of the workday. A 10- or 12-hour shift does not get a longer denominator.

For substances with additive health effects, §5155(c)(1) and Appendix (B) require calculation of D, the sum of each substance’s TWA divided by its own PEL. Appendix (B) states that the value of D shall not exceed unity. Effects are presumed additive unless there is information to the contrary. The appendix lists situations where effects are not treated as additive, such as when the individual substances affect different organs of the body.

Under §5155(d), substances marked “S” may be absorbed into the bloodstream through the skin, mucous membranes and/or the eye and contribute to overall exposure. The subsection requires that appropriate protective clothing be provided for and used by employees as necessary to prevent skin absorption. Air sampling does not measure that route, so a clean air result on an “S” substance does not settle skin contact.

When Monitoring Is Required: §5155(e)

Section 5155(e) is short and specific.

  • (e)(1) Trigger. Whenever it is reasonable to suspect that employees may be exposed to concentrations in excess of the levels permitted in §5155(c), the employer shall monitor, or cause to have monitored, the work environment so exposures can be measured or calculated. The trigger is reasonable suspicion, not confirmed overexposure.
  • (e)(2) Controls. When exposures are found or expected to exceed allowable levels, control measures shall be instituted in accordance with §5141. Section 5141 puts engineering controls first whenever feasible, then administrative controls if practicable, then respirators under §5144 in the situations it lists.
  • (e)(3) Competence. The person supervising, directing or evaluating the monitoring and control methods shall be versed in the standard and competent in industrial hygiene practice.
  • (e)(4) Records. All monitoring results shall be recorded and retained in accordance with §3204. Section 3204(d)(1) requires employee exposure records to be preserved for at least thirty years.

A note to subsection (e) states that screening of the work environment by any person authorized by the employer, using appropriate measuring devices, is encouraged. That is encouragement, not a mandate, but screening is often the fastest way to decide whether (e)(1) has been triggered.

Medical Surveillance Under §5155(f)

Section 5155(f) states that a medical surveillance program approved by the Division may be required to ensure satisfactory maintenance of employee health and to ascertain the effectiveness of the control methods. The word is “may.” Section 5155 itself does not set an automatic medical surveillance program for every Table AC-1 substance. Substance-specific standards often do, so confirm which rule governs a chemical first. Where surveillance records are generated, §3204 governs retention of employee medical records.

What to Do This Week

  1. Pull the safety data sheets for your highest-use chemicals and confirm, by CAS number, whether each one is governed by a substance-specific standard or by §5155.
  2. For each §5155 substance, read its current Table AC-1 row, including footnotes, and note whether it carries a PEL, STEL, ceiling and “S” notation.
  3. Identify tasks where exposure above any of those limits is reasonable to suspect, and schedule monitoring designed for the limit that applies.
  4. Check whether any blends require a D calculation under the Appendix.
  5. Confirm that past monitoring results are filed where they will survive the §3204 retention period.

If you need a sampling strategy built around Table AC-1, or a review of exposure data you already have, see my industrial hygiene services and chemical exposure assessment pages, and for surveillance and records questions, my recordkeeping and medical surveillance page. To request a consultation, call (626) 546-9384.

Need help with a Cal/OSHA matter?

McNeil Safety Consulting provides Cal/OSHA citation defense, industrial hygiene, safety plan writing, and expert witness services throughout California. Call (626) 546-9384 or request a consultation.