Methylene Chloride Under Cal/OSHA 8 CCR 5202

By Michael Karl McNeil, REP, RIH, EPP, QSD

Methylene chloride (MC) is a fast-acting solvent found in paint strippers, adhesive removers, degreasers, and some coating and foam operations. It evaporates quickly, so airborne levels in a small room or an enclosed booth can climb fast. In California, occupational exposure is governed by Title 8, California Code of Regulations, section 5202, a full substance-specific standard with its own exposure limits, monitoring schedule, regulated area rules, respirator restrictions, and medical surveillance program. This post covers what the section requires, with a focus on the paint stripping and furniture refinishing work where problems show up most often, and a brief note on the federal EPA rule that now sits on top of it.

Scope and Exposure Limits

Section 5202(a) applies the standard to all occupational exposures to methylene chloride in general industry, construction, and shipyard employment. The standard itself names paint stripping, polyurethane foam manufacturing, and cleaning and degreasing as examples of the activities it reaches.

The numbers are in 5202(b) and (c):

  • Permissible exposure limit (PEL): 25 ppm as an 8-hour time-weighted average, under 5202(c).
  • Short-term exposure limit (STEL): 125 ppm over a 15-minute sampling period, under 5202(c).
  • Action level: 12.5 ppm as an 8-hour TWA, defined in 5202(b).

Employee exposure under 5202(b) means the exposure that would occur if the employee were not wearing a respirator. A worker in a respirator in a 60 ppm room is still exposed above the PEL for purposes of the standard, which drives monitoring, regulated areas, and medical surveillance.

Exposure Monitoring

Section 5202(d) requires the employer to determine each affected employee’s exposure using breathing zone air samples representative of the 8-hour TWA and the 15-minute short-term exposures. The initial determination can be skipped only in the situations the section allows, such as objective data showing MC cannot be released at or above the action level or STEL under foreseeable conditions, or qualifying prior monitoring. Results must meet the accuracy limits in 5202(d) at a 95 percent confidence level.

After the initial round, Table 1 in 5202(d)(3) sets periodic monitoring by result:

  • Below the action level and at or below the STEL: no periodic monitoring required.
  • Below the action level and above the STEL: STEL sampling every 3 months.
  • At or above the action level, at or below the TWA and STEL: TWA sampling every 6 months.
  • Above the TWA: TWA sampling every 3 months, with STEL sampling every 3 months where the STEL is also exceeded.

Two consecutive results at least 7 days apart can step monitoring down: to every 6 months once results are at or below the TWA PEL, off entirely for TWA once below the action level, and off for STEL once at or below the STEL. Section 5202(d)(4) requires additional monitoring when workplace changes, such as a process or control change, may increase exposure, and after a spill, leak, rupture, or breakdown once cleanup and repairs are done.

Employees must be notified of their results in writing within 15 working days of the employer receiving them. If results exceed the PEL or STEL, the notice must describe the corrective action and the schedule for it. When I review MC programs, the missing piece is usually the STEL sample. Stripping is a burst activity, and an 8-hour TWA alone can look acceptable while short-term peaks are well over 125 ppm.

Regulated Areas

Under 5202(e), the employer must establish a regulated area wherever an employee’s exposure exceeds, or can reasonably be expected to exceed, the 8-hour TWA PEL or the STEL. Inside that area:

  • Access is limited to authorized persons.
  • Anyone entering must be supplied with a respirator under 5202(g), and must use it when exposure is likely to exceed the limits.
  • Activities that could increase dermal or oral exposure are prohibited, as are activities that interfere with the respirator seal while one is worn.
  • The boundaries must be clearly demarcated.

On multi-employer sites, the employer establishing the regulated area must communicate its location and access restrictions to the other employers.

Controls and Respirators

Section 5202(f) puts engineering and work practice controls first. They must be used to reduce exposure to or below the PELs except where they are not feasible, and respirators supplement them where controls alone fall short. Employee rotation is prohibited as a means of compliance. Leaks and spills must be detected and handled promptly.

The respirator rules in 5202(g) are where MC differs from most solvents. Under 5202(g)(3)(A), the employer must provide appropriate atmosphere-supplying respirators. Half masks of any type are prohibited, because MC may cause eye irritation or damage. Because 5202(g)(3)(A) calls for atmosphere-supplying respirators, an organic vapor cartridge respirator does not meet it for routine use. The only air-purifying device the section names is a gas mask with an organic vapor canister, and only for emergency escape under 5202(g)(3)(B). The respirator program must meet section 5144.

In practice, for a stripping operation, that means supplied air or a change of chemistry. Many shops find that local exhaust ventilation plus a lower-hazard stripper is less burdensome than a supplied-air program. That is a business decision, but it should be made with monitoring data in hand, which is what a chemical exposure assessment provides.

Protective Clothing, Hygiene, and Eyewash

Section 5202(h) requires MC-resistant protective clothing and equipment, at no cost to the employee, where needed to prevent skin or eye irritation, with eye and face protection meeting section 3382. Section 5202(i)(1) requires conveniently located washing facilities where skin contact with solutions containing 0.1 percent or more MC is reasonably foreseeable, and 5202(i)(2) requires appropriate eyewash facilities within the immediate work area for emergency use where eye contact with those solutions is reasonably foreseeable. Check glove permeation data for methylene chloride specifically.

Medical Surveillance

Section 5202(j)(1) requires the employer to make medical surveillance available to employees who are or may be exposed at or above the action level on 30 or more days per year, or above the 8-hour TWA PEL or the STEL on 10 or more days per year; to employees exposed above the PEL or STEL for any time period whom a licensed health care professional has identified as at risk from cardiac disease or another serious MC-related condition and who request inclusion; and to employees exposed during an emergency. It must be provided at no cost, without loss of pay, at a reasonable time and place.

The program runs on a schedule set by the standard. There is initial surveillance at or before assignment. Under 5202(j)(4)(B), the medical and work history is updated annually, and examinations recur within 12 months for employees 45 or older and within 36 months for employees under 45, unless the physician’s written opinion recommends a different frequency. The section also covers emergency exposures, the written medical opinion to employer and employee, and medical removal protection. The clinical content is set by the standard and the examining physician, not the employer. The employer’s job is to identify who qualifies, arrange the evaluations, and keep the records required by 5202(m), which for medical surveillance means the duration of employment plus 30 years.

Paint Stripping and Furniture Refinishing

Table 1 in 5202(d)(3) lists furniture refinishing, general aviation aircraft stripping, boat building and repair, upholstery, and construction work such as painting and paint removal, cabinet making, and floor refinishing among the operations it calls out by name. These are often small enclosed rooms where stripper is applied by hand and scraped off close to the breathing zone, which produces high short-term peaks.

The federal EPA rule adds another layer. Under the Toxic Substances Control Act, EPA amended 40 CFR Part 751, Subpart B in 2024 (89 FR 39296, May 8, 2024). For conditions of use that continue under its Workplace Chemical Protection Program, 40 CFR 751.109(c) sets an existing chemical exposure limit of 2 ppm as an 8-hour TWA and an EPA STEL of 16 ppm over 15 minutes. Under 40 CFR 751.107(b)(8), industrial and commercial use of methylene chloride for refinishing wooden furniture, decorative pieces, and architectural fixtures is prohibited after May 8, 2029, with interim requirements in 751.117 until then. Check the current eCFR text before relying on any federal date. The EPA rule does not replace section 5202; both apply.

What to Do This Week

  1. List every product on site containing methylene chloride, using the safety data sheets, and identify who uses each one and where.
  2. If you have no current air sampling, schedule both TWA and 15-minute STEL sampling for each task.
  3. Check your respirator inventory. If anyone is using a half mask or cartridge respirator for MC work, stop and reassess.
  4. Confirm an eyewash is within the immediate work area wherever stripper is applied.
  5. Read 40 CFR 751 Subpart B against your operations and note any federal dates that affect you.

If you need monitoring, a written exposure control plan, or help deciding whether to keep MC in your process, see industrial hygiene services, request a consultation, or call (626) 546-9384.

Need help with a Cal/OSHA matter?

McNeil Safety Consulting provides Cal/OSHA citation defense, industrial hygiene, safety plan writing, and expert witness services throughout California. Call (626) 546-9384 or request a consultation.