Scissor lifts and boom lifts are often handed to whoever is nearest after a five-minute walkaround. California regulates them in Article 24 of the General Industry Safety Orders, Title 8, Sections 3636 through 3648, which splits the equipment into two categories with different operating rules and different fall protection requirements. This article covers the two categories, the manual and plate, inspection and records, operating rules, fall protection, operator instruction and energized lines.
Two Categories of Equipment
Title 8, Section 3637 defines the terms that sort the equipment:
- Elevating work platform. A device designed to elevate a platform in a substantially vertical axis. The definition lists vertical towers, scissor lifts and mast-climbing work platforms.
- Aerial device. Any vehicle-mounted or self-propelled device, telescoping extensible or articulating, or both, which is primarily designed to position personnel. Articulating booms and extensible boom platforms are defined as aerial devices.
A scissor lift is an elevating work platform and operates under Title 8, Section 3646. A boom lift or bucket truck is an aerial device and operates under Title 8, Section 3648. Title 8, Section 3636(b) excludes other equipment from the article, including mobile ladder stands and scaffold towers, industrial trucks and firefighting equipment.
The Manual, the Plate and the Qualified Person
Title 8, Section 3638 applies to both categories.
- Manual. Each unit must have a manual containing instructions for maintenance and operations, kept in a weather resistant storage location on the unit (Section 3638(a) and (a)(1)).
- Plate. Each unit must have a conspicuously displayed, legible plate or marking verifying that it was designed and manufactured to the applicable ANSI standard listed in Section 3638(b). Section 3638(c) lists the required plate data, including rated capacity at the maximum platform height.
- Assembly. Units must be assembled and erected by a qualified person in accordance with the manufacturer’s specifications and maintained in safe operating condition (Section 3638(e)).
On rented equipment the manual box is empty more often than it should be. Section 3638 makes no exception for rented units, so I advise checking for the manual and a readable plate at delivery and sending the unit back if either is missing.
Inspection, Maintenance and Records
Title 8, Section 3640(a)(1) requires inspection, maintenance and repairs to be performed by a qualified person in accordance with the manufacturer’s specifications. Section 3640(d) requires records of inspections and repairs to be maintained for at least three years and made available to the Division upon request. Inspection records must show the date, any deficiencies found, the corrective action recommended and who performed the inspection. Repair records must show the date, the work done and who performed it.
Separate from that inspection and maintenance work, Section 3646(c) requires elevating work platforms to be inspected for damaged and defective parts before use. For aerial devices, Section 3648(b) requires lift controls to be tested in accordance with the manufacturer’s recommendations or instructions prior to use. Article 24 does not prescribe a form for the pre-use check. I recommend a dated checklist drawn from the manufacturer’s manual and kept with the unit.
Operating Rules Under Sections 3646 and 3648
Scissor Lifts and Other Elevating Work Platforms
The platform must meet Title 8, Section 3642: a guardrail 42 inches high, plus or minus 3 inches, with a midrail, toeboards at least 3 1/2 inches high at sides and ends, upper and lower controls on powered units, and an emergency stopping device at the upper controls. Section 3646 then sets the operating rules:
- Units must be assembled, used and disassembled in accordance with the manufacturer’s instructions (Section 3646(b)).
- Units may not be loaded beyond the design working load, and a unit damaged or weakened from any cause must be taken out of service until repairs are completed (Section 3646(d)).
- Employees may not sit, stand or climb on the guardrails or use planks, ladders or other devices to gain height or reach (Section 3646(e)).
- Employees may not work on units when exposed to high winds or storms, or when the units are covered with ice or snow, unless provisions have been made for their safety (Section 3646(f)).
- Riding a traveling elevated platform is allowed only where travel speed at maximum travel height does not exceed 3 feet per second, self-propelled units have the required interlocks, and the surface is level with no hazardous irregularities or debris (Section 3646(a)).
Title 8, Section 3645(a) prohibits using an elevating work platform on an inclined surface unless the manufacturer recommends it for that use.
Boom Lifts and Other Aerial Devices
Section 3648 sets the rules for aerial devices:
- Only authorized persons may operate an aerial device (Section 3648(c)).
- Belting off to an adjacent pole, structure or equipment while working from an aerial device is not permitted (Section 3648(d)).
- The manufacturer’s boom, basket and platform load limits may not be exceeded (Section 3648(f)).
- Outriggers, when used, must be positioned on pads or a solid surface, and wheel chocks must be installed before use on an incline where they can be safely installed (Section 3648(h) and (i)).
Section 3648(l) prohibits moving an aerial device truck with the boom elevated and employees in the basket unless every listed condition is met, including equipment specifically designed for that operation, a speed of no more than 3 miles per hour, only one employee in the basket, and specific training for that work.
Fall Protection in Each Category
Section 3648(o) requires an employee in an elevated aerial device to be secured to the boom, basket or tub through a safety belt, body belt or body harness equipped with a safety strap or lanyard, with one exception for certain orchard man-lifts. The subsection sets limits on the equipment:
- Safety belts and body belts are prohibited in personal fall arrest systems. They may be used in a fall restraint or positioning device system (Section 3648(o)(1)).
- A belt used for positioning must be rigged so the employee cannot free fall more than 2 feet (Section 3648(o)(2)).
- A body harness used for fall arrest must have a lanyard rigged with a deceleration device that limits the maximum arresting force to 1,800 pounds, limits free fall to a maximum of 6 feet, and prevents the employee from hitting any level or object below (Section 3648(o)(3)).
Section 3646 has no counterpart to Section 3648(o). For a scissor lift, the fall protection written into Article 24 is the guardrail system in Section 3642(a). That subsection adds one condition: where the guardrail is less than 39 inches high, an approved personal fall protection system must be used in accordance with Section 3648(o). Section 3646(b) requires units to be used in accordance with the manufacturer’s instructions, so check what the manual for each unit says about lanyards and anchor points. Many general contractors and facility owners also require tie-off in scissor lifts by site rule.
Operator Instruction and Energized Lines
Section 3638(d) requires employees to be instructed in the proper use of the platform in accordance with Article 24, the manufacturer’s operating instructions, and the Injury and Illness Prevention Program under Title 8, Section 3203. For elevating work platforms, Section 3646(l) requires that instruction to come from a qualified person and to reach employees who erect, disassemble, move, operate, use, repair, maintain or inspect the equipment. Section 3646(l)(1) lists the minimum content: the provisions of Section 3646; the correct procedures for the employee’s assigned duties; the hazards associated with the equipment, including electrical, fall and falling object hazards, and the procedures for dealing with them; safe operation and material handling on the platform; and the maximum load capacity based on the installed configuration.
On energized lines, Section 3638(f) requires work with elevating work platforms or aerial devices in proximity to energized high voltage lines to be done in accordance with Article 37 of the High-Voltage Electrical Safety Orders, and its note points to the Low Voltage Electrical Safety Orders for work below 600 volts. Article 24 does not state clearance distances itself, so lift training has to bring in those electrical orders wherever overhead lines are within reach.
What to Do This Week
- Open the manual box on every lift on site, owned or rented, and confirm the operating manual is there and the plate is legible.
- Pull inspection and repair records and check that they go back three years and show dates, deficiencies, corrective action and who did the work.
- Check that every boom lift has a harness and lanyard assigned to it and that operators are connecting to the anchor point in the basket.
- Read the fall protection section of each scissor lift manual and measure any guardrail that looks low against the 39-inch threshold.
- Compare your lift training outline to the five topics in Section 3646(l)(1) and document who delivered it.
- Identify overhead lines at each work location before a lift is positioned.
I provide equipment-specific lift instruction and written operating procedures for employers through my safety training services. Request a consultation through the site or call (626) 546-9384.