Cal/OSHA Construction Ladders: Section 1675 and Section 3276

By Michael Karl McNeil, REP, RIH, EPP, QSD

Contractors looking for Cal/OSHA’s construction ladder rules usually expect a long section full of measurements. What they find in the Construction Safety Orders is much shorter. 8 CCR §1675, “General,” the first section of Article 25 (Ladders), runs four subsections. Most of the detailed requirements a construction crew has to meet live in the General Industry Safety Orders, which §1675 pulls onto the jobsite by reference. Knowing how that cross-reference works is the key to building a ladder program that holds up on inspection. This post covers what §1675 says, how it hands portable ladders to §3276, and what §3276 requires day to day.

What Section 1675 Actually Says

The current section has four subsections:

  • §1675(a) General requirements. “Except where either permanent or temporary stairways or suitable ramps or runways are provided, ladders described in this section shall be used to give safe access to all elevations.”
  • §1675(b) Portable ladders. All portable ladders used in construction shall comply with Section 3276 of the General Industry Safety Orders.
  • §1675(c) Fixed ladders. All fixed ladders used in construction shall comply with Sections 3277 and 3278 of the General Industry Safety Orders, titled “Fixed Ladders” and “Use of Fixed Ladders.”
  • §1675(d) Single-rail ladders. “Single-rail ladders shall not be used.”

The history note explains why the section is so lean. A rulemaking operative in January 2011 repealed the former subsections (b) through (n) and replaced them with the two cross-references now in (b) and (c). A 2012 amendment added the single-rail prohibition in (d). Older training materials that quote construction-specific ladder measurements from §1675 may be describing text that no longer exists.

Subsection (a): Access to Every Elevation

Section 1675(a) is an access rule. Where workers have to reach an elevation, the employer must provide either a stairway (permanent or temporary), a suitable ramp or runway, or a ladder meeting the article. Climbing formwork, stacked materials or equipment is not one of the options.

When I walk a site, I look for decks or excavations that crews reach by climbing whatever is handy because the ladder was moved elsewhere. The rule is satisfied only when proper access is actually in place where the work is.

Job-Made Ladders: Section 1676

Article 25 has one other active section. 8 CCR §1676, “Job-Made Ladders,” governs ladders built on site, with detailed requirements for lumber grade, cleat dimensions and spacing, rail size by ladder length, and fastening. Two provisions come up often:

  • §1676(a) requires a double cleat ladder when a ladder is the only means of access or exit for 25 or more employees, or when two-way traffic is expected.
  • §1676(j) states that double-head nails shall not be used in ladder construction.

If your crews build ladders, the carpenter building them needs §1676 in hand, not a general rule of thumb.

How §3276 Applies to Construction Portable Ladders

Because §1675(b) adopts §3276 for all portable ladders used in construction, the General Industry portable ladder section is the construction rule for stepladders, single ladders and extension ladders. I covered §3276 in detail in the post on Cal/OSHA portable ladders under Section 3276. The provisions that matter most on a jobsite:

  • Selection, §3276(d)(1). Scaffolds or other worker positioning equipment shall be used when work cannot be safely done from ladders. When selecting a ladder, consideration shall be given to length or height, working load, duty rating, worker position and frequency of use. The duty classifications and their rated loads appear in §3276(d)(2).
  • Inspection, §3276(e)(2). Ladders shall be inspected by a qualified person for visible defects frequently and after any occurrence that could affect their safe use.
  • Damaged ladders, §3276(e)(3). Defective ladders shall be withdrawn from service for repair or destruction and tagged or marked “Dangerous, Do Not Use” or similar language. Ladders with broken or missing steps, rungs, cleats, safety feet or side rails shall not be used.
  • Footing, §3276(e)(7). The base shall be on secure and level footing, not on boxes, barrels or other unstable bases, and not on ice, snow or slippery surfaces unless suitable means to prevent slippage are used.
  • Angle, §3276(e)(9). Single and extension ladders shall, where possible, be set so the horizontal distance from the top support to the foot is one-quarter of the working length. The ladder shall be placed to prevent slipping or be tied, blocked, held or otherwise secured.

Landings, Placement and Electrical Hazards

Construction work brings its own conditions: changing levels, vehicle traffic and temporary power. Several §3276 provisions speak directly to them.

  • Upper landings, §3276(e)(11). When a portable ladder is used to reach an upper landing, the side rails shall extend not less than 36 inches above the landing surface. When that is not possible, the ladder shall be secured at its top to a rigid support that will not deflect, and a grasping device such as a grab-rail shall be provided.
  • Multiple ladders, §3276(e)(10). When two or more separate ladders are used to reach an elevated work area, they shall be offset with a platform or landing between them, subject to the exception stated for portable ladders used to reach elevated fixed ladders.
  • Traffic areas, §3276(e)(14). Ladders shall not be placed in passageways, doorways, driveways or anywhere they may be displaced by other work, unless protected by barricades or guards.
  • Clear areas, §3276(e)(19). The area around the top and bottom of a ladder shall be kept clear.
  • Electrical hazards, §3276(e)(18). Non-conductive ladders shall be used where the ladder or user may contact unprotected energized electrical conductors or equipment. Conductive ladders must carry a caution marking against use around electrical equipment.
  • Extension ladders, §3276(e)(12) and (e)(13). Ladders shall not be tied together to make longer sections unless designed for it, and extension ladders shall be erected with the fly section above and resting on the base section with the rung locks engaged. Minimum overlap requirements by ladder length are set out in §3276(e)(16).

Climbing and Working Rules

How a ladder is used matters as much as its condition. Section 3276(e)(15) sets the rules:

  • The user shall face the ladder when ascending or descending and maintain contact at three points at all times, §3276(e)(15)(C).
  • Employees shall be prohibited from carrying equipment or materials that prevent safe use of the ladder, §3276(e)(15)(B).
  • Work shall be done with the body near the middle of the rung, without overreaching; the employee shall descend and reposition the ladder when necessary, §3276(e)(15)(A).
  • No standing and working on the top 3 rungs of a single or extension ladder unless structural members provide a firm handhold or the employee is protected by a personal fall protection system, §3276(e)(15)(D).
  • No sitting, kneeling, stepping or standing on the pail shelf, topcap or the step below the topcap of a stepladder, with an exception when that step is located 18 inches under the topcap, §3276(e)(15)(E). Planks shall not be used on the top step or topcap, §3276(e)(16)(B).

Training Is Part of the Rule

Section 3276(f) requires that before an employee uses a ladder, the employee be provided training in safe ladder use, unless the employer can demonstrate the employee is already trained as the subsection requires. Supervisors of employees who routinely use ladders must also be trained. The subsection lists seven topics, from selection and inspection through erection, climbing, factors contributing to falls and prohibited uses. The training may be delivered as part of the Injury and Illness Prevention Program required by §3203. Because §1675(b) adopts §3276 in full, this training requirement applies to construction crews using portable ladders.

What to Do This Week

  1. Walk each active area and confirm every elevation has a stairway, ramp, runway or compliant ladder in place, as §1675(a) requires.
  2. Pull any damaged ladder from service and tag it “Dangerous, Do Not Use.”
  3. Check landing access ladders for the 36-inch extension or a secured top with a grab-rail.
  4. Replace conductive ladders anywhere near unprotected energized equipment.
  5. Confirm ladder training records exist for crews and their supervisors.

For crew and supervisor ladder training built around §3276(f), see my OSHA safety training services, or schedule a jobsite safety audit. To request a consultation, call (626) 546-9384.

Need help with a Cal/OSHA matter?

McNeil Safety Consulting provides Cal/OSHA citation defense, industrial hygiene, safety plan writing, and expert witness services throughout California. Call (626) 546-9384 or request a consultation.