Drills, grinders, saws, and nailers are in almost every shop and maintenance room in California, and they rarely get a second look until something goes wrong. Cal/OSHA does not treat them as ordinary. The General Industry Safety Orders set specific rules for how a portable tool is switched on and off, how it is grounded, how a grinder wheel is guarded and mounted, and who answers for a tool’s condition. Below are the sections that apply and where employers come up short when I review their tool programs.
Where the Portable Tool Rules Live
The core rules sit in Title 8, Group 3 of the General Industry Safety Orders. Article 20, “Hand and Portable Powered Tools and Equipment,” covers §§3555 through 3564, including the general duty section, switch requirements, pneumatic and powder-actuated tools, jacks, and portable winches. Two older sections in that article, §3560 (Portable Grinders) and §3561 (Portable Sanders), are listed as repealed, so a reference to either one in an old safety manual is a sign the manual needs updating.
Abrasive wheels have their own article. Article 21, “Use, Care, and Protection of Abrasive Wheels,” runs from §3575 through §3583, and §3583 is the section written specifically for portable abrasive wheels. Grounding of cord-and-plug tools is not in the General Industry Safety Orders at all. It is in the Electrical Safety Orders at §2395.45.
The Employer Owns the Condition of Every Tool
Section 3556 is short, and it carries more weight than its length suggests. Under §3556(a), each employer is responsible for the safe condition of tools and equipment used by employees, and the text expressly includes tools and equipment the employees furnish themselves. Section 3556(b) restricts tools to the purposes for which they were designed, and §3556(c) states that unsafe hand tools shall not be used.
The employee-owned tool language is easy to overlook. Supervisors often assume a worker’s own drill is the worker’s business. The regulation says otherwise. If an employee uses a personal angle grinder with the guard removed on your floor, the condition of that grinder is your responsibility under §3556(a). A practical tool program puts personal tools through the same inspection and tag-out process as company tools, or bars them from the site.
Switches and Controls: Constant-Pressure, Lock-On, and On-Off
Section 3557 decides what kind of switch a hand-held powered tool must have, and it sorts tools into three groups.
- §3557(a), constant-pressure control only. Hand-held powered circular saws with a blade diameter greater than 2 inches, electric, hydraulic, or pneumatic chain saws, and percussion tools without a positive accessory holding means must have a constant-pressure switch or control that shuts off power when pressure is released. Gasoline-powered chain saws must have a constant-pressure throttle control that shuts off power to the saw chain.
- §3557(b), constant-pressure control, lock-on permitted. Hand-held powered drills, tappers, fastener drivers, horizontal, vertical, and angle grinders with wheels greater than 2 inches in diameter, disc sanders with discs greater than 2 inches, belt sanders, reciprocating saws, saber, scroll, and jig saws with blade shanks greater than a nominal 1/4 inch, and other similarly operating tools must have a constant-pressure switch. They may also have a lock-on control, but only if turnoff can be accomplished by a single motion of the same finger or fingers that turn it on.
- §3557(c), positive on-off control permitted. Platen sanders, grinders with wheels 2 inches in diameter or less, disc sanders with discs 2 inches or less, routers, planers, laminate trimmers, nibblers, shears, and saber, scroll, and jig saws with blade shanks a nominal 1/4 inch wide or less may use a positive on-off control or any other control the section allows.
The section defines “nominal” in (b) and (c) as plus or minus 0.05 inch. Under §3557(d), the operating control on hand-held power tools must be located to minimize accidental operation where that would create a hazard to employees. The section does not apply to concrete vibrators, concrete breakers, powered tampers, jack hammers, rock drills, garden, household, kitchen and personal care appliances, medical or dental equipment, or fixed machinery.
The field problem is modification. A taped-down trigger or a zip-tied paddle switch turns a compliant tool into one that keeps running after it leaves the operator’s hand.
Grounding and Double Insulation
Section 2395.45 of the Electrical Safety Orders requires exposed metal parts of cord-and-plug connected equipment that may become energized to be grounded under any of the conditions it lists. Subsection (a)(2) covers equipment operated at more than 150 volts to ground. Subsection (a)(3) lists equipment types, and several apply directly to tools: (C) hand-held motor-operated tools, stationary and fixed motor-operated tools, and light industrial motor-operated tools; (D) motor-operated tools and equipment such as drills, sanders, and saws; (G) portable hand lamps; and (H) tools likely to be used in wet and conductive locations.
There are two exceptions. Listed portable tools likely to be used in wet and conductive locations need not be grounded if they are supplied through an isolating transformer with an ungrounded secondary of not over 50 volts. And listed or labeled portable tools protected by an approved system of double insulation need not be grounded, provided the equipment is distinctively marked.
In practice this means two things. A three-prong tool with the ground pin broken off is out of compliance, because the tool depends on that ground path. And outside the isolating-transformer exception, a two-prong tool is acceptable only if it is listed or labeled as double insulated and carries the distinctive marking.
Pneumatic Tools, Nailers, and Powder-Actuated Tools
Section 3559 has three requirements. Under §3559(a), safety clips or retainers must be installed on pneumatic impact tools to prevent dies and tools from being accidentally expelled from the barrel, unless other effective means are used. Under §3559(c), hand-held pneumatic tools that drive nails, staples, or similar fasteners and operate at 100 psig or more line pressure must have a safety device at the muzzle that prevents discharge until the muzzle contacts a solid surface. Disabling or bypassing a nailer’s contact tip defeats that device.
Powder-actuated tools are handled by reference. Section 3559(b) requires powder-actuated tools used in industrial operations to be designed, constructed, operated, and maintained in compliance with Article 27 of the Construction Safety Orders. Check that your plant safety program reflects that cross-reference.
Portable Grinders and Abrasive Wheels
Under §3583(a), abrasive wheels may be used only on machines provided with the safety guards required by §3577(b). Section 3577(b) requires hoods or guards that protect employees from flying pieces of a broken wheel, as far as the operation permits, with eight listed exceptions. Two of those apply to portable work: Type 1 wheels 2 inches or less in diameter and 1/2 inch or less thick on portable drill mandrels below 1800 SFPM, and mounted wheels 2 inches or smaller used in portable operations.
The guard geometry is specific. For vertical portable grinders with a right-angle head, §3583(d) sets a maximum guard exposure angle of 180 degrees, requires the guard to be between the operator and the wheel during use, and requires it to be adjusted so pieces of a broken wheel are deflected away from the operator. For other portable grinders, §3583(e) limits angular exposure of the wheel periphery and sides to 180 degrees and requires the top half of the wheel to be enclosed at all times.
Mounting is where wheels fail. Section 3583(f)(1) requires each wheel to be closely inspected and sounded by the user immediately before mounting, and requires the spindle speed of the machine to be checked so it does not exceed the maximum operating speed marked on the wheel. Section 3583(f)(2) through (4) address fit on the spindle, clean and flat contact surfaces, and bushings that must not exceed the wheel width or contact the flanges. A larger wheel forced onto a smaller grinder, with the guard removed to make room, can violate several of these at once, starting with the speed check.
Eye protection is also in play. Section 3382(a) requires the employer to provide and ensure use of suitable eye or face protection where employees are exposed to eye injury hazards from flying particles, and grinding is a textbook example.
What to Do This Week
- Pull every grinder and circular saw from the crib and check for missing guards, taped or tied triggers, and wheels larger than the tool was built for.
- Check every two-prong tool for the double-insulation marking, and every three-prong tool for an intact ground pin.
- Look at the nailers: confirm the muzzle safety device works and has not been bypassed.
- Bring employee-owned tools into your inspection process or bar them from the site.
- Read your written tool policy for references to repealed §3560 or §3561 and update it.
If you want an outside set of eyes on your tool program, a safety audit covers Article 20, Article 21, and the electrical grounding rules together, and tool safety training can be built around the equipment your crews actually use. To request a consultation, call (626) 546-9384.