Crane Operator Certification in California: Title 8, Sections 5006.1 and 5006.2 After the Repeal of Section 1618.1

By Michael Karl McNeil, REP, RIH, EPP, QSD

I still see lift plans, subcontract terms and safety manuals that cite Title 8, Section 1618.1 of the Construction Safety Orders for crane operator certification. That section was repealed effective July 26, 2022. The current rules are Section 5006.1 for general industry and Section 5006.2 for construction, both in Group 13 of the General Industry Safety Orders. This article covers who must be certified, who may certify, the exceptions each section lists, the employer evaluation required in construction, trainee limits and recertification.

Which Section Applies to Your Crane

Section 1610(a) of the Construction Safety Orders now says cranes and derricks used in construction shall comply with General Industry Safety Orders, Group 13, except as supplemented in that section. Three sections in Group 13 carry the operator rules:

  • Section 5006: only employees authorized by the employer and trained in the safe operation of cranes or hoisting apparatus may operate that equipment, and trainees may operate under the supervision of a qualified operator. Its exception sends mobile and tower cranes to Section 5006.1.
  • Section 5006.1: operator qualifications and certification for mobile cranes and tower cranes. The heading states it is applicable to cranes in general industry only.
  • Section 5006.2: operator training, certification and evaluation for cranes and derricks in construction.

Section 5006.2(h) provides that operators trained, certified under Option 1 and evaluated under Section 5006.2 are qualified to work on projects in construction and in general industry. Section 5006.1 has no matching provision.

Certification in General Industry

Under Section 5006.1(a), the employer shall only permit operators who have a valid certificate of competency, issued by an Accredited Certifying Entity for the type of crane to be used, to operate a crane covered by the section. Certificates are issued to operators who:

  1. Pass a physical examination conducted by a physician or other licensed health care professional, using at a minimum the criteria in ASME B30.5-2000, Chapter 5-3.1.2(a)(1-5, 7, 8), or the US DOT requirements in 49 CFR Sections 391.41 through 391.49.
  2. Pass a substance abuse test conducted by a recognized laboratory service, at a level consistent with standard practice for the industry where the crane is in use.
  3. Pass a written examination covering, among other items, operational characteristics and controls, emergency control skills, load charts, supporting ground, site hazards and site access.
  4. Pass a “hands-on” examination on the specific type of crane, including pre-start and post-start inspection, maneuvering skills, shutdown and securing procedures.

Section 5006.1(c) defines the Accredited Certifying Entity. The crane operator testing organization must be accredited by an approved nationally recognized accrediting agency, and that accreditation must be reviewed at least every three years. A certificate from a training vendor that is not accredited this way does not meet subsection (a).

The section lists three exceptions:

  • Mobile cranes having a boom length of less than 25 feet or a maximum rated load capacity of less than 15,000 pounds.
  • Operators of electric line trucks (digger derrick trucks) as defined in Section 2700 and regulated by Section 2940.7. The exception does not include mobile truck cranes designed and built to ASME B30.5.
  • Marine terminal operations regulated by Article 14.

I read Section 5006(a) as still applying to an excepted crane, because the Section 5006 exception reaches only mobile and tower cranes regulated by Section 5006.1. The operator must be authorized by the employer and trained.

Certification in Construction

Section 5006.2(a) requires the employer to ensure each operator is trained, certified or licensed, and evaluated before operating equipment covered by Group 13, unless the person is operating as an operator-in-training under subsection (b). Subsection (c) gives two routes: Option 1, certification by an accredited crane operator certifying entity (subsection (d)), or Option 2, a license from a government entity that meets the criteria in subsection (e). Under (c)(1), the employer provides the certification or licensure at no cost to employees.

The Option 1 criteria in subsection (g) track the general industry list: physical examination, substance abuse test, written examination and hands-on examination. Under (d)(1)(A), an operator is deemed qualified to operate a particular piece of equipment if certified for that type, or type and capacity, or for higher-capacity equipment of that type, and the certificate must state the type of equipment. An Option 2 license is good only within the jurisdiction of the government entity and for no longer than 5 years ((e)(3)).

The construction exceptions differ from the general industry ones:

  • Derricks, sideboom cranes, and equipment with a maximum manufacturer-rated hoisting/lifting capacity of 2,000 pounds or less. The note keeps the training and qualification requirements of Section 5006 in place for these.
  • Articulating/knuckle-boom cranes with a boom length of less than 25 feet or a maximum rated load capacity of less than 15,000 pounds, when used to deliver material to a construction site.
  • Digger derrick trucks and marine terminal operations, in the same terms as Section 5006.1.

Section 5006.2 does not repeat the general industry exception for every mobile crane under 25 feet of boom or 15,000 pounds of capacity. Its version is limited to articulating/knuckle-boom cranes delivering material.

The Employer Evaluation in Construction

A certificate does not complete the construction requirement. Section 5006.2(f)(1) requires the employer to ensure, through an evaluation, that each operator has demonstrated:

  • The skills and knowledge, and the ability to recognize and avert risk, necessary to operate the equipment safely, including those specific to its safety devices, operational aids, software, and size and configuration. Size and configuration includes lifting capacity, boom length, attachments, luffing jib and counterweight set-up.
  • The ability to perform the hoisting activities required for assigned work, including, if applicable, blind lifts, personnel hoisting and multi-crane lifts.

The evaluator must have the knowledge, training and experience necessary to assess equipment operators ((f)(3)) and must be an employee or agent of the employer, who retains the duty when an agent is used ((f)(4)).

Under (f)(5), the employer documents the evaluation with the operator’s name, the evaluator’s name and signature, the date, and the make, model and configuration of the equipment used. The document must be available at the worksite while the operator is employed by the employer. For operators employed before April 6, 2020, (f)(2) allows the employer to rely on its previous assessments, and the documentation then reflects the date of the employer’s determination and the equipment on which the operator previously demonstrated competency. Where I see contractors fall short is a certification card in the file and no evaluation document for the crane on site.

Section 5006.1 has no evaluation subsection.

Trainees and Operators-in-Training

Both sections allow a trainee to operate under direct supervision. The supervisor must be in the immediate area, within visual sighting distance and able to communicate effectively with the trainee, and shall have no other duties other than to observe the operation of the crane by the trainee (Sections 5006.1(e) and 5006.2(b)(4)(A)). The supervisor must hold a valid certificate of competency for the type of crane. In construction, the operator’s trainer must also be an employee or agent of the trainee’s employer.

Under Sections 5006.1(e)(1) and 5006.2(b)(3), an operator-in-training shall not operate the equipment:

  • If any part of the equipment, load line or load, operated up to the maximum working radius in the work zone, could get within 20 feet of a power line that is up to 350 kV, or within 50 feet of a power line over 350 kV.
  • To hoist personnel.
  • In multiple-equipment lifts.
  • Over a shaft, cofferdam, or in a tank farm.
  • In multiple-lift rigging operations, except where the operator’s trainer determines that the trainee’s skills are sufficient for this high-skill work.

Section 5006.2(b)(5) requires retraining when the operator’s performance or an evaluation of the operator’s knowledge indicates it is necessary, and (f)(6) requires a re-evaluation afterward.

Recertification Every Five Years

Certificates are valid for a maximum of five years, and operators re-certify every five years (Sections 5006.1(b) and (d); 5006.2(d)(1) and (d)(3)). An operator with at least 1,000 hours of documented experience operating the specific type of crane during the immediately preceding certification period, who meets the physical examination, substance abuse and written examination requirements, is not required to retake the hands-on examination.

What to Do This Week

  • Search your lift plans, subcontracts and safety manual for “1618.1” and replace it with Section 5006.1 or 5006.2.
  • Pull each operator’s certificate, confirm the type of crane it states matches the crane the operator runs, and record the expiration date.
  • For construction work, confirm an evaluation document with the four items in Section 5006.2(f)(5) exists for each operator and is at the worksite.
  • For each trainee, name the certified operator who supervises, confirm that person has no other duties, and check the work against the five prohibited operations.
  • Start an hours log by crane type for every operator, for the 1,000-hour provision at recertification.
  • Check any crane you treat as exempt against the exception list for the section that applies.

For help reviewing operator qualification files and crane procedures on a construction project, see my construction safety services or call (626) 546-9384.

Need help with a Cal/OSHA matter?

McNeil Safety Consulting provides Cal/OSHA citation defense, industrial hygiene, safety plan writing, and expert witness services throughout California. Call (626) 546-9384 or request a consultation.