Point-of-operation guarding gets most of the attention in machine safety, but the drive side of a machine carries its own caught-in hazards: the V-belt and sheave behind a side panel, the line shaft under a bench, the sprocket and chain on a conveyor head. California regulates those parts in a separate group of the General Industry Safety Orders. This post covers the sections that apply to belts, pulleys, shafting, gears and sprockets.
Where These Rules Sit, and What They Leave Out
Mechanical power transmission falls under Group 6 of the General Industry Safety Orders, titled “Power Transmission Equipment, Prime Movers, Machines and Machine Parts.” The relevant articles are Article 37 (purpose, definitions and standards, §§3940 through 3945), Article 43 (shafting, collars, clutches and couplings), Article 44 (pulleys), Article 45 (belt and pulley drives, §§4070 through 4072), Article 46 (gears, friction drives, sprockets and chains, §§4075 through 4077) and Article 47 (power disconnecting devices).
Section 3940 states that these orders cover guarding of power transmission equipment, prime movers and machine parts and do not include point of operation hazards. The note to §4002 sends point-of-operation questions to Group 8, which begins at §4184. If the hazard is where the machine cuts, shapes or forms the work, that is a different analysis, covered in my post on point-of-operation guarding under §4184. If the hazard is the machinery that moves power to that point, you are in Group 6.
One practical warning: several sections in these articles have been repealed, including §4052, §4061, §4072, §4077 and §4085. A citation, audit report or written program that relies on one of those numbers was built from an old reference and needs to be corrected.
The Definitions That Decide Most Disputes
Section 3941 defines “guarded” as shielded, fenced, enclosed or otherwise protected according to the orders so as to remove the hazard of accidental contact. “Enclosed” is a stricter term: the moving parts are guarded so that physical contact by parts of the body is precluded. When a section says “enclosed,” a guard that merely makes contact unlikely does not meet it.
Section 3941 also defines the “nip-point” as the location along the inrunning side of rotating parts that permits a part of the body to be caught, and “machine parts” as all moving parts of the machine except those forming part of the point of operation. “Belts” covers all power transmission belts, including flat, round and V-belts.
Belts and Pulleys: §4070 and the Seven-Foot Line
The core rule is §4070(a): all moving parts of belt and pulley drives located 7 feet or less above the floor or working level shall be guarded. The section lists a short set of exceptions in §4070(a)(1) through (6), including sewing machines, which it routes to §4475.
- Guard bottoms. Under §4070(b), the bottom of a guard need not be enclosed where it is within 4 inches of the floor or supporting structure.
- Overhead belts. Under §4070(d), horizontal overhead belts more than 7 feet above the floor must be guarded for their full length where they run over passageways or work areas.
- Belt dressing and fasteners. Section 4070(g) requires dressing of a moving belt or rope to be done at a safe distance from the nip point, and §4070(h) requires metallic fasteners or lacings to be clinched so nothing projects from the belt surfaces or edges.
Section 4071 adds that counterweighted belt tighteners must be of substantial construction, with either a device that keeps the tightener from dropping if the belt breaks or a standard railing guard around the floor area beneath it, placed 15 to 20 inches from the vertical projection of the tightener’s outermost parts. Section 4060 adds belt guides, stops on overhanging flat pulleys, and belt perches for idle belts on line shafts and countershafts.
Shafting, Shaft Ends, Keys and Set Screws
Under §4050(a), exposed parts of line or countershafting, collars, clutches, cut-off couplings and clutch pulleys seven feet or less above the floor or working level shall be guarded. Section 4050(b) requires shafting over a driveway to be enclosed or fitted with a trough guard unless it is 15 feet or more above the driveway or is part of an overhead traveling crane. Section 4050(c) lists the acceptable methods for shafting under benches. Section 4050(d) reaches shafting that crosses or runs parallel to elevated runways, walkways, catwalks or platforms when it is within seven feet vertically or within 15 inches of either side.
Shaft ends are their own item. Section 4051(a) requires projecting shaft ends within 7 feet of the floor or working level to be rounded and smooth at the edge and tip, projecting no more than one-half the diameter of the shaft beyond the bearing unless guarded by a nonrotating casing. Section 4051(b) requires exposed unused keyways at that height to be filled, covered or guarded.
Section 4002 fills the gaps. Under §4002(a), machines, machine parts and component parts with hazardous revolving, reciprocating, running, shearing or punching motion, including pinch points and shear points not protected by the machine frame or by location, must be guarded. Under §4002(b), keys, set screws and projections that create a hazard must be removed, made flush or guarded. A protruding set screw on a rotating collar is easy to miss on equipment that otherwise looks well guarded.
Gears, Sprockets and Chain Drives
Section 4075(a) requires gears, sprockets and sprocket chain drives located 7 feet or less above the floor or working level to be guarded. Section 4075(b) addresses band guards, which must extend inward past the root of the teeth, with spokes covered by a disk guard. Where employees pass under chain drives, §4075(c) applies the requirements of §3943(c) and (f). For overhead silent chain drives, §4075(d) requires guards to clear the nearest moving chain part by at least one-quarter inch, or one-half inch on drives with centers more than 20 inches apart.
What Makes a Guard Compliant: §§3942 Through 3944
Having a guard is not the same as having a compliant guard. Section 3942(a) requires guards to be appropriate for the hazards involved, secured in place, built of substantial materials consistent with Table G-1, and free of hazardous projections. Section 3942(b) requires hinged or removable sections where belts must be replaced, settings changed or lubricant added.
Section 3943 sets construction standards. Horizontal overhead belt guards must be at least 25% wider than the belt, with side clearance that need not exceed 6 inches on each side, under §3943(e). Under §3943(f), horizontal overhead rope and chain drive guards must be at least 6 inches wider than the drive on each side, and where employees pass underneath, a shallow trough or other effective means must be strong enough to carry a broken chain.
Section 3944 ties opening size to distance. Guards within 2 inches or within 4 inches of moving parts must have openings small enough to stop a one-half inch object, per §3944(a) and (b). Between 4 and 15 inches, openings must stop any object larger than 2 inches, and slatted openings may be no wider than 1 inch, under §3944(c). Standard railing guards must sit not less than 15 nor more than 20 inches from moving parts under §3944(d). When I measure a field-fabricated guard, I check the opening-to-distance relationship first.
Guards Come Off: Servicing and Lockout
Belt changes, tensioning, chain lubrication and sprocket replacement all require a guard to come off, which moves the job under §3314. Section 3314(c) requires machinery capable of movement to be stopped and the power source de-energized or disengaged, with moveable parts mechanically blocked or locked out if necessary. Section 3314(d) requires prime movers and machines with lockable controls, or controls readily adaptable to lockout, to be locked out or positively sealed in the off position. Section 3314(g) requires a written hazardous energy control procedure.
A guard left off after maintenance is a recurring finding in the facilities I review. Adding a final step to each lockout procedure to reinstall the guard before the lock comes off is good practice, not a separate rule.
What to Do This Week
- Walk each production line and list every belt, pulley, shaft, gear, sprocket and chain drive within 7 feet of a floor or working level, including elevated walkways and platforms.
- Check each guard against §3942 through §3944: secured, no hazardous projections, opening size matched to distance, and access sections for adjustment and lubrication.
- Look for projecting shaft ends, unused keyways and exposed set screws under §4051 and §4002(b).
- Confirm that every drive requiring guard removal has a written energy control procedure under §3314(g).
- Remove any reference to repealed sections from your written programs and audit checklists.
If you want a second set of eyes on your drive-side guarding, or you have received a citation under Group 6, request a consultation through my safety audit service or the Cal/OSHA citation defense page, or call (626) 546-9384.